Analisa Kinerja Mesin Roughing Stand dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) dan Failure Mode Effect Analysis (FMEA)

Authors

  • Hasrul Hasrul Universitas Serang Raya
  • M. Jihan Shofa Universitas Serang Raya
  • Heru Winarno Universitas Serang Raya

DOI:

https://doi.org/10.30656/intech.v3i2.879

Keywords:

Failure Mode and Effect Analysis, Overall Equipment Effectiveness, Roughing Stand Machine

Abstract

The roughing stand machine functions for steel/product formation and the roll has five stands, and from each position has a different turn. In the production process, this machine also experiences obstacles that hinder the process [of production]. This study aims to determine the value of Overall Equipment Effectiveness (OEE) and analysis of the causes of OEE values have not been maximized based on the review of Failure Mode and Effect Analysis (FMEA). The data used are historical data of roughing stand machines during July 2016-December 2016. Based on the data processing performed, the results of the Overall Equipment Effectiveness (OEE) obtained on the Roughing Stand machine purchased at 57.5. The potential failure priority is base on the order of Risk Priority Number (RPN), the screw up non-working item has the most considerable RPN value (56). Regular lubrication is one way to maximize screw up performance..

Downloads

Download data is not yet available.

References

Adianto, H., Sitompul, C., & Susana, S. (2005). Penerapan Model Preventive Maintenance Smith dan Dekker di PD. Industri Unit Inkaba. Jurnal Teknik Industri, 7(1), 51–60.

Ahuja, I. P. S., & Khamba, J. S. (2008). Total productive maintenance: literature review and directions. International Journal of Quality & Reliability Management, 25(7), 709–756.

Limantoro, D. (2013). Total Productive Maintenance di PT. X. Jurnal Titra, 1(1), 13–20.

Muchiri, P., & Pintelon, L. (2008). Performance measurement using overall equipment effectiveness (OEE): literature review and practical application discussion. International Journal of Production Research, 46(13), 3517–3535.

Nakajima, S. (1988). Introduction to TPM: total productive maintenance. Productivity Press, Inc.

Nakajima, S. (1989). TPM development program: implementing total productive maintenance. Productivity press Cambridge.

Pujotomo, D., & Kartha, R. (2007). Analisa Sistem Perawatan Komponen Bearing Bottom Roller Dan V Belt Mesin Ring Frame Ry-5 Pada Departemen Spinning II a (Di PT Danliris Surakarta). J@ Ti Undip: Jurnal Teknik Industri, 2(2), 40–48.

Rinawati, D. I., & Dewi, N. C. (2014). Analisis Penerapan Total Productive Maintenance (TPM) Menggunakan Overall Equipment Efectiveness (Oee) Dan Six Big Losses Pada Mesin Cavitec Di PT. Essentra Surabaya. Prosiding SNATIF, 21–26.

Wijaya, C. Y., & Widyadana, I. G. A. (2015). Pengukuran Overall Equipment Effectiveness (OEE) di PT Astra Otoparts Tbk. Divisi Adiwira Plastik. Jurnal Titra, 3(1), 41–48.

Downloads

Published

2017-12-28

How to Cite

Hasrul, H., Shofa, M. J., & Winarno, H. (2017). Analisa Kinerja Mesin Roughing Stand dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) dan Failure Mode Effect Analysis (FMEA). Jurnal INTECH Teknik Industri Universitas Serang Raya, 3(2), 55–60. https://doi.org/10.30656/intech.v3i2.879

Issue

Vol. 3 No. 2 (2017)

Section

Articles